Kenmore Appliance Repair in Orange County

Kenmore appliances were never made by Sears. They were built to order by Whirlpool, LG, Frigidaire, GE and others, and sold under one badge. So the first thing we do on a Kenmore call is read the model number, because a Kenmore washer and a Kenmore refrigerator in the same kitchen may have come from two entirely different manufacturers.

What Kenmore builds

Kenmore covered almost every category a household needed, which is why so many Orange County homes still have one. The important detail for repair is the model prefix: 110 is normally Whirlpool-built laundry, 795 is usually LG refrigeration, 253 tends to be Frigidaire, and 665 is commonly a Whirlpool dishwasher. Elite and Pro sat at the upper end of the range. Once the builder is known, the diagnosis is the same as for that manufacturer.

What we are called about most

Top-load washer will not spin
On the Whirlpool-built 110-series machines this is the lid lock or the shift actuator, exactly as it is on a Whirlpool or Maytag of the same era. The parts carry different numbers but the failure and the repair are identical.
Refrigerator warm with the fans running
On LG-built 795-series units this can be the linear compressor. On Frigidaire-built 253-series units it is more often the defrost control or the evaporator fan. The model prefix decides which of the two we investigate first.
Dishwasher will not start
The 665-series dishwashers are Whirlpool platform, and the usual causes are the door latch switch or the control board behind the panel. A blinking indicator on these is a stored fault code, not simply a reminder light.
Dryer tumbles without heating
Common across every builder that made Kenmore dryers. On electric models it is the element or a thermal cut-off that has opened, and a blocked vent run is very often the reason the cut-off opened in the first place.
Parts ordered against the wrong platform
The frequent Kenmore mistake, and the reason a repair gets delayed. Searching by brand alone returns parts for the wrong manufacturer entirely. We order against the full model number, prefix included, every time.

Kenmore repairs by appliance

What people say

5 from 1,610 reviews

  • Two-zone wine column in Newport Beach held the lower zone fine and let the upper drift warm. The evaporator fan had seized. Once that was replaced both zones settled and the compressor finally started cycling off.

    Rafael O.Newport Beach★★★★★

  • Dryer would not power on at all. The door switch had failed and the thermal fuse had opened from a restricted vent. He replaced both and cleaned the duct, which was the actual cause.

    Faye T.Brea★★★★★

  • Gas dryer shut off hot part-way through. The thermal cut-off had opened because the vent was restricted. He cleared the duct and replaced the fuse. Some lint ended up on the floor, which I had to sweep.

    Jarrod T.Seal Beach★★★★☆

Kenmore questions

How do I find out who made my Kenmore?

Read the first three digits of the model number on the data plate. They identify the manufacturer: 110 is generally Whirlpool, 795 is usually LG, 253 tends to be Frigidaire. Send us the full model number and we will confirm before the visit.

Where is the model number on a Kenmore appliance?

On washers and dryers it is usually inside the lid or door opening, or on the back panel. On refrigerators it is commonly on the inside wall near the crisper, and on dishwashers along the edge of the door frame.

Are Kenmore parts still available?

For most machines, yes, once the builder is known. Parts are ordered against the underlying manufacturer platform rather than the Kenmore badge. Some Sears-specific trim and control panels are harder to source, and we check availability before committing to a repair.

Is a Kenmore worth repairing now Sears has gone?

Usually. The machines were built by manufacturers who are still trading, and mechanical parts remain widely available. Proprietary electronics are the exception. We check parts availability against your model number first and tell you if a repair is not sensible.

Have the Kenmore model number to hand

The model and serial plate tells us which platform the machine is on, which decides what the fault is likely to be and whether the part is still made.

(949) 979-4880 Book online

$89 to come out, and nothing extra on top once a repair is agreed.